interface |
您所在的位置:网站首页 › interface interface-type › interface |
Syntaxinterface-type (nbma | p2mp | p2mp-over-lan | p2p) {
ipsec-sa;
ldp-synchronization {
(disable | enable);
hold-time;
}
metric;
mtu;
neighbor address {
eligible;
}
no-advertise-adjacency-segment;
no-eligible-backup;
no-eligible-remote-backup;
no-interface-state-traps;
no-neighbor-down-notification;
node-link-protection;
passive {
traffic-engineering {
remote-node-id;
remote-node-router-id;
}
}
poll-interval;
priority;
retransmit-interval;
secondary;
te-metric;
topology (default | ipv4-multicast | name);
transit-delay;
bandwidth-based-metrics;
bfd-liveness-detection;
dead-interval;
demand-circuit;
disable;
dynamic-neighbors;
flood-reduction;
hello-interval;
link-protection;
own-router-lsa;
}
Hierarchy Level[edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name],
[edit logical-systems logical-system-name protocols ospf3 realm (ipv4-multicast | ipv4-unicast | ipv6-multicast) area area-id interface interface-name],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-multicast | ipv4-unicast | ipv6-multicast) area area-id interface interface-name],
[edit protocols (ospf | ospf3) area area-id interface interface-name],
[edit protocols ospf3 realm (ipv4-multicast | ipv4-unicast | ipv6-multicast) area area-id interface interface-name],
[edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name],
[edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-multicast | ipv4-unicast | ipv6-multicast) area area-id interface interface-name]
Description Specify the type of interface. By default, the software chooses the correct interface type based on the type of physical interface. Therefore, you should never have to set the interface type. The exception to this is for NBMA interfaces, which default to an interface type of point-to-multipoint. To have these interfaces explicitly run in Nonbroadcast multiaccess (NBMA) mode, configure the nbma interface type, using the IP address of the local ATM interface. In Junos OS Release聽9.3 and later, a point-to-point interface can be an Ethernet interface without a subnet. DefaultThe software chooses the correct interface type based on the type of physical interface. Optionsnbma (OSPFv2 only)Nonbroadcast multiaccess (NBMA) interface p2mpPoint-to-multipoint interface p2mp-over-lanPoint-to-multipoint over LAN mode p2pPoint-to-point interface The remaining statements are explained separately. See CLI Explorer. Required Privilege Levelrouting鈥擳o view this statement in the configuration. routing-control鈥擳o add this statement to the configuration. Release InformationStatement introduced before Junos OS Release聽7.4. Support for OSPFv3 for interface type p2p only introduced in Junos OS Release聽9.4. You cannot configure other interface types for OSPFv3. Support for OSPFv3 for interface type p2mp is introduced in Junos OS Release 18.1R1. Support for OSPFv3 for interface type p2p only introduced in Junos OS Release聽9.4 for EX Series switches. |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |